How to Drill Into Tile?

Drilling can seem tough, but it’s actually easier when you do it. I learned the process when we installed hardware on our tiled walls. We hired a carpenter to do the job, as we didn’t know how to drill into tile without cracking it. But as we saw him perform the drilling, I understood that you just need to be precise and patient. The most important part is the measurement, and you can easily do it.

Get Free Estimate

How Do You Drill Through Tile?

You need to know what type of tile you have. We have a ceramic tile, which is quite common these days. And these tiles are in fact easy to drill through, as compared to other tiles like glass and porcelain. Since we have a ceramic tile, I am sharing the drilling process for the same.

• Before marking the drill points, the carpenter measured about three times just to confirm placing holes in the right spots. 

• Then, he used masking tape over the area. He explained it is done to create an additional tension, which prevents the drill bit from slipping.

• As a next step, he positioned the drill bit with the marking and started drilling steadily. Later, he said that it’s important to be patient and not rush through the process, which can lead to inaccuracy and cracked tiles. 

• Once you see the hole, increase the pace and pressure and, while doing it, keep spraying water on the tile, to prevent overheating. 

The process of

how

to drill through tile can seem overwhelming, but you just have to be patient and steady with the drilling. If you are unsure of handling it alone, take professional help for better safety. 

I hope your question on how do I drill into tile, is clear now.

I learned how to drill through tile from our carpenter. It takes severe precision to do such a task or you might end up breaking the tile. He used several items to execute the task professionally, like a drill, goggles, gloves and others. I watched the entire process thoroughly so I can share it with you here.

How do You Drill Through Tile?

To drill through tiles, you will need items like:

• Goggles and gloves, 

• Electric drill, 

• Masking tape

• Wall Plug and others, if needed

Let me now answer your query: how do I drill into tile using these items:

• Mark the Spot: 

Use masking tape to mark the drilling spot on the tile, which helps prevent the drill bit from slipping.

• Secure the Tile: 

Place the tile on a stable surface and ensure it's secured firmly to prevent movement while drilling.

• Start Drilling: 

Position the drill at a low speed and apply gentle pressure. Begin drilling at a 45-degree angle to create a guide dimple.

• Adjust Angle: 

Once the dimple is made, gradually increase the angle to 90 degrees and continue drilling with steady pressure.

As you near completion, reduce the pressure on the drill to avoid chipping the tile. Once through, remove the masking tape and clean up any debris. I hope this answers your question: how do I drill into tiles. I am not an expert; hence, I will refrain from drilling a hole but you can try it at home.

Read More:

Hi, Pal

Get Free Estimate

Do you want to install hardware for toilet paper rolls and soap dishes or a new medicine cabinet on the tile and do not know how to drill into tile wall? Then, let me assist you in this. Putting holes in tiled walls, whether in a newly tiled bathroom or an existing one, is a common task. 

There are various determinants to be taken into consideration before drilling into tiles.

• Determine the type of tile you have

Glazed ceramic tile is the most common, and it's the easiest to drill through. You'll find it in almost every older property.

• Have the proper ceramic tile bit

Standard drill bits will not operate on tile, but that's not a problem. A carbide bit can be used to drill ceramic tile, while a diamond-tipped bit is required for glass and porcelain.

• Set the stage for success by arranging the wall

It's been said that you should measure twice and cut once, but given the repercussions of drilling a hole in the wrong spot in a tile wall, you should measure three times and drill once. This will also help you in knowing how to drill into wall tiles without cracking them

• First, tape the place where you'll drill to the wall with masking tape

On tape, it's easier to precisely designate the hole location than on tile.

• Drill gradually

To ensure that the hole ends up where you want it, go slowly, especially at start.

You can raise the drill speed once the hole is started, but not to full speed.

Drill the hole with steady pressure and a medium speed to avoid overheating and ruining the drill bit.

• At the conclusion, pick up the pace

When the bit passes through the tile, you'll notice a difference in resistance. You can now increase the drill's speed while reducing the pressure. This will allow you to expand the hole into the drywall or backer board while causing the least amount of damage possible.

After you've finished drilling, press the anchors into position, secure the hardware, and vacuum up the dust.

I hope this answer would help you in knowing how to drill into tile wall.

Read More: