How To Clean Chimney Mesh Filter at Home?

Here is how to clean chimney mesh filter at home.

• First, switch off the chimney and unplug it for safety. Wait until it cools down completely. 

• Then remove the mesh filter carefully by following the instructions in your chimney manual.

• Next, fill a large bucket or sink with hot water. 

  • Add a few drops of dishwashing liquid and 2 to 3 tablespoons of baking soda. 

  • You can also add a little white vinegar for extra grease-cutting power. Mix everything well.

• Place the mesh filter in the solution and let it soak for 20 to 30 minutes. This helps loosen the grease and dirt stuck inside the tiny holes of the filter.

• After soaking, use a soft brush or an old toothbrush to gently scrub both sides of the filter. 

  • Pay extra attention to the corners where grease usually collects. 

  • Avoid using a steel scrubber because it can damage the mesh.

• Once the filter looks clean, rinse it thoroughly under running water. Make sure all the soap and grease are washed away. Shake off the excess water and leave the filter to dry completely. You can also wipe it with a clean cloth.

• When the filter is fully dry, place it back in the chimney and make sure it fits properly.

For best performance, clean the mesh filter every two to four weeks if you cook daily. Regular cleaning improves suction, reduces bad smells, and helps your chimney last longer. It also prevents grease from building up, making your kitchen cleaner and safer for everyday cooking.

Hi Gowtham. You can use baking soda, salt and vinegar to clean the mesh filter of your chimney. I have been using this method to frequently clean the chimney. So, I will be able to help you with how to clean chimney mesh filter at home using the same method. Let me sescirbe the procedure in steps below.

Process for Chimney Mesh Filter Cleaning

1. Start by removing the filter carefully.

2. Take the filter and place it in a tub and pour boiling water.

3. After this, you need to add 2.3 tbsp of baking soda, salt and 1 cup of vinegar.

4. Let the filter soak for some time, and then take it out.

5. Clean the filter with fresh water and wipe it dry.

This is how to clean kitchen chimney mesh filter. I hope it helps.

Get a Clean Chimney with Expert Care Via NoBroker!

Some related information:

How to clean chimney Plates?

If you are careful enough with the right tools, cleaning a chimney mesh filter at home is something that can be quite simple. I have recently cleaned a mesh filter of my chimney using dishwashing liquid. So, let me share a step-by-step guide on how to clean chimney mesh filter.

How to Clean Kitchen Chimney Mesh Filter?

• Before starting the process, I ensure that the chimney has cooled off completely and nobody is using it. I wore gloves and goggles to avoid debris and dirt.

• I took out the detachable mesh filter from the chimney in accordance with the manufacturer’s instructions. I unscrewed it from its base.

• On the outside, I gently shook off any loose soot or other small particles of dust that may have accumulated on the filter. If it is heavily greasy or dirty, you may want to put it on a large sheet or tarpaulin to capture anything that drops.

• Then, in a bucket, I mixed some warm water and added several drops of dishwashing liquid soap into this mixture. If there’s an excessive buildup of grease, you may also consider introducing some vinegar for added degreasing power.

• I put this mesh filter inside soapy water then used a soft brush to clean it by gently rubbing it to remove the dirt accumulation. Don’t scrub hard because it could damage the netting

• I then washed the filter with clean water and rinsed it well to ensure that all of the soap was removed. Afterwards, I shook off excess water and let the filter air dry completely before reattaching it to the chimney.

• Once the filter dried out, then it was time to put it back in the chimney again. I tightened the screws nicely and reinstalled it. .

I hope you understood the steps on how to clean mesh filter of kitchen chimney. However, this is a lengthy and time consuming process and you can hire cleaning professionals to do it. 

Read More

Over the years, chimneys have become an important part of modern kitchens. They help keep the smoke, vapors, and smell out of the kitchen. But maintaining them in an Indian kitchen is quite tricky. So, how to clean chimney mesh filter at home? 

Oil and spices are the main reasons mesh chimney filters get dirty quickly. But you can clean them with ease. Here are a few steps to clean them. 

How To Clean Kitchen Chimney Mesh Filter?

Here are the steps that you can follow for cleaning chimney mesh filter. 

• You need water, a few spoons of detergent powder, a toothbrush, and a big utensil for boiling water to get started. 

• Fill the utensil with water and boil it. Ensure the utensil is big enough to fit the mesh filter without any hassle. 

• Add the detergent and then the chimney to the boiling water. 

• Let the water boil with the mesh for some time. The filter will start cleaning itself. 

• Use the toothbrush to clean the grime of the mesh. 

• Now, use clean water to wash it and let it dry. 

And that’s how to do chimney mesh filter cleaning. Mesh filters are not suitable for Indian kitchens. But if you already have it, cleaning it every week is the best choice and will ensure it lasts longer. I hope your query about how to clean chimney mesh filter at home has been answered.