How to Repair Jaquar Taps?

My Jaguar kitchen mixer tap was leaking a few days back. I hired a plumber to get my Jaguar taps repaired. The plumber highlighted that most leakage issues are due to worn out rubber washers or loose fittings. He was able to handle the leak by using a screwdriver, wrench, and a new washer. I can share the steps that he followed.

Get Free Estimate

How to Repair Jaquar Tap Leakage?

1. The water supply was turned off using the valve beneath the sink. Plugged the drain to prevent screws from falling in.

2. Then, using a screwdriver, he took out the tap handle.

3. He took out the old washer, changed to a new one that is of the correct size.

4. Finally, he reattached every component, and gradually turned on the water again, to identify any further leaks.

Though the steps seem to be a DIY task, I still hired a plumber, as I lacked the expertise of fixing it correctly.

Get Assistance in Repairing, Installation, or Replacement of a Tap at an Affordable Rate Via NoBroker Plumbing Solutions!

Hello Tarun, I’d like to help you by sharing how to repair Jaquar tap leakage. I have Jaquar fittings in my kitchen and bathroom. I observed leakage in the kitchen sink t

How to Fix Jaquar Tap?

1. Start by plugging the drain and turning off the water supply. If you can’t find the valves, look for the pipe underneath the sink and turn off the knob or handle at its end. 

2. You then need to dismantle the tap. The process will depend on the kind of tap you have. 

3. You’ll require a screwdriver, wrench or spanner to twist the tap’s handle out of its place.

4. Remove the screws of the tap handles. You may need to remove the cold and hot embellishments to get to the screws. 

5. After removing the handles, take off the nut. You can find it on top of the washer seat, made up of rubber.

6. Detach the wash seat slowly. Replace the wash seat as the rubber is one of the reasons for leakage at times. Ensure the new one fits correctly.

7. Reassemble the tap with the help of your screwdriver and wrench. 

8. Turn on the water supply and slowly open the tap. Check for leaks and also the flow of the water.

This is all. I hope you now know how to repair Jaquar mixer tap.

Jaquar tap repairing is a relatively simple procedure when done carefully and deliberately. There are a few steps involved in this repair process: identifying the problem, cutting the water supply, removing the broken component, reassembling the mixer, and turning on the water supply. Read this answer to get the detailed procedure.

Get Free Estimate

How to Repair Jaquar Mixer Tap?

Upon researching the most straightforward method for fixing a Jaquar mixer tap online, I discovered a YouTube video demonstrating the process. Before starting with the process, assemble the required equipment, including a screwdriver, adjustable wrench, and extra parts if necessary. 

I have mentioned the steps below for your reference:

• Determine the tap's issues. Leaks, low water pressure, or a broken handle are common problems. 

• To catch any drips, turn off the water supply and put a towel or cloth underneath the tap.

• Now, take off the handle by carefully unscrewing it. 

• To remove the spindle, unscrew the bonnet nut with an adjustable wrench. 

• Check for the O-rings and washers for any signs of damage. Replace them as needed. 

• Put the tap back by doing the reverse procedures.

• Finally, test for leaks before tightening the nut all the way.

Sometimes, mineral accumulation could be the reason for low water pressure. This problem can be resolved by unscrewing the aerator in an anticlockwise direction. You just have to soak it in vinegar for several hours, give it a good water rinse, and replace it. I hope now you have an idea of Jaquar kitchen tap repair tips.

There are many things in the house that keep on breaking. Pipes and taps are on top of the list for me. I can see the taps in my kitchen and washroom leaking every few weeks. To make sure, I don't have to call a plumber. I learned how to repair jaquar taps from Youtube. This is what I learned. 

The first step in jaguar taps repair is figuring out what part of the tap has been damaged. You need to make a quick assessment of the tap and check the valve seat, valve body, washer, handle, bonnet nut and other parts. 

As you begin to repair the damaged tap, switch off the main water supply. This will ensure you don't waste any water during the repairs.

After step 1 and 2 are completed, you can repair the damaged part. If you don't know the process of  jaguar tap repairing. You can call a professional plumber.

You can repair the leakage in the tap by opening the handle of the tap and easily tightening the washer with the help of a wrench. 

I hope now you know how to repair jaquar taps.

Read more :